In Projects

We may receive a commission when you use our affiliate links. However, this does not impact our recommendations.

To offer four faces with quartersawn white oak on each leg, the leg centers are glued then planed to 1-5/8" x 1-3/8". Then the 1/8" or 1/4" oversize "skins" of quartersawn veneer are glued to the flat-sawn faces. After the glue dries, plane the legs to their finished 1-1/2" x 1-1/2" dimension.

To offer four faces with quartersawn white oak on each leg, the leg centers are glued then planed to 1-5/8" x 1-3/8". Then the 1/8" or 1/4" oversize "skins" of quartersawn veneer are glued to the flat-sawn faces. After the glue dries, plane the legs to their finished 1-1/2" x 1-1/2" dimension.

A Morris chair (heck, almost any chair) just isn’t complete without an ottoman to prop your feet on. Sadly, by the time you finish building the chair you’re usually so glad to have completed the project that the ottoman gets delayed until later. Well, now is the time!

We’ve published a number of plans for Morris chairs in Popular Woodworking (most recently in our special Great American Furniture publication) in varying styles and by several designers. After looking at dozens of comparable ottomans, we selected a traditional and simple design from Gustav Stickley.

The #300 ottoman we used as a model is one of Stickley’s earlier pieces. Originally offered with a hard leather seat, it sold for $7.50 in the 1912 catalog. Recent auctions have seen this simple piece sell for as much as $800.

The dimensions on our project match Stickley’s, but we’ve updated the seat material to adjust the cost (as well as to make it a little more comfortable).

How to Build It

Choosing the best grain pattern to face "forward" is a tough call. In any case, take a close look at the grain on the pieces for your legs and mark the tops to offer the best look.

Choosing the best grain pattern to face "forward" is a tough call. In any case, take a close look at the grain on the pieces for your legs and mark the tops to offer the best look.As far as furniture projects go, this is pretty simple. But it does give you a chance to work on a hallmark joint of Arts & Crafts furniture – the mortise and tenon. There are four mortises per leg, but for the first-time builder the construction method used is very forgiving. The blind tenons, including the ones in the top rail joints (which ultimately are hidden by the upholstery) make this project pretty simple. The simplicity of the mortise-and-tenon joint is spruced up a little on this piece with the addition of pegs, which make the joints more solid and add a nice decorative touch. The more significant step only sharp-eyed woodworkers will notice at first is to make the legs from multiple pieces of wood. By doing so, the highly figured quartersawn white oak shows on all four sides. Mother Nature hasn't figured out how to do this yet, but we have. The mortises for the top rails are on adjacent inside faces and intersect in the middle of the leg. The mortises for the lower rails are staggered to fit one on top of the other. I used a benchtop hollow-chisel mortiser to make quick work of the mortises, but a router (or even a chisel and mallet) will work just as well.

Also, if upholstery is something that has kept you from trying this type of project before, don’t sweat it. I’m hardly an upholsterer myself, and everyone who has seen my ottoman seems to think it turned out pretty well.

Four-faced Legs
Quartersawn white oak is one of the features that dresses up the plain styling of Arts & Crafts furniture. Cut from the center of the log out to the bark, the orientation of the growth rings runs almost perfectly perpendicular to the face of the board. This reveals splashes of “ray flake” that are beautiful to behold, but they only happen on the perpendicular faces.

There are a couple of good ways to give the legs this “ray flake” on all four faces, but Stickley chose to simply add quartersawn veneer to the two flatsawn faces, which I copied.

Start making the legs by cutting eight leg halves that are 7/8″ x 2″ x 16″. The 7/8″ thickness will require you to start with 4/4 rough lumber, but ultimately the oversized dimensions will be to your benefit, as you’ll see.

The shoulders for all the rail tenons are made with little fuss on the table saw. Define the shoulder on the first pass using a miter gauge for support, then nibble the rest of the material away, backing the piece away from the rip fence.

The shoulders for all the rail tenons are made with little fuss on the table saw. Define the shoulder on the first pass using a miter gauge for support, then nibble the rest of the material away, backing the piece away from the rip fence.

First, glue each of the four leg pairs together, face-to-face, orienting the best quartersawn grain pattern to the outside. When the glue has dried, square one corner of each piece on the jointer, then size each leg (using your table saw, then your jointer for a final pass) to 1-5/8″ (across the face that shows a seam) x 1-3/8″ or slightly larger (across the quartersawn face).

These dimensions will allow you to add 1/8″-thick veneer to the two layered faces, then run the entire leg down to 1-1/2″ square, leaving an almost invisible veneer face on two sides.

Next, run eight veneer pieces to 1/8″ x 1-3/4″ x 16″. If 1/8″ is thinner than you’re comfortable running on your planer, leave it at 1/4″ – just know that you’ll have to plane more off those faces after glue-up. Glue the veneer pieces to the leg blanks, making sure the veneer extends over all the edges.

After the glue has dried, trim the veneer pieces flush to the leg centers (I used a No. 3 hand plane). Then run the veneer faces through the planer (alternating sides on each pass) until the leg is 1-1/2″ square. Trim the legs to length for a four-faced leg.


Product Recommendations

Here are some supplies and tools we find essential in our everyday work around the shop. We may receive a commission from sales referred by our links; however, we have carefully selected these products for their usefulness and quality.

Recommended Posts

Start typing and press Enter to search

I make a leg template on thin plywood (right) and trace the pattern on two adjacent sides of the leg blank (left). I then band saw the piece to shape (center).Mark each of the pieces as either inside or outside, as well as the ends that will need rabbet cuts, to avoid making mistakes once you're at the machine.